Despatch Protocol Plus Controller (Heat Only) Manual de usuario Pagina 23
- Pagina / 56
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Protocol Plus Owner’s Manual OPERATION
Version 2 23
Copyright © 2010 by Despatch Industries.
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
5.3. Timer Mode
1. Press Select until Timer displays.
O
Press Run at any time in the procedure to activate Timer Mode.
2. Press Menu to display the Process Temperature Setpoint (Setpt). Change Setpoint
(Setpt) by using ▲ or ▼ to change the value.
O
If the SPChange on the Enable page in Setup Mode has been set
to DISABLED, it must be changed to ENABLED before any
changes to the process temperature and high limit setpoints can
be made.
3. Press Menu a second time to display current high limit setpoint (Hi-Lim SP). Change
Setpoint (Hi-Lim SP) using ▲ or ▼. If Band displays, the high limit band feature is
activated (see Control page, Section 8.1.5) and the high limit cannot be adjusted.
4. Press
Menu a third time to display Time Set. Change the time setting by using ▲ or ▼.
5. Optional Feature: Press
Menu a fourth time to display Event1. Press ▲ to turn the
event ON or ▼ to turn the even OFF. Repeat for all events which are enabled (up to
four events).
6. Press Menu a fifth time to display the current guaranteed soak band (TmrGuarSoak)
value. If the process temperature deviates from the setpoint by more than this value,
the timer is placed in a Hold condition. The timer continues when the process
temperature falls within range. Reference the Quick Reference and Default Values
section (Section 8.1) for available settings.
7. To start Timer Mode, press Run. The display changes from Stop to Run and the time
remaining displays. Return to Stopped Mode by pressing Stop. While in operation,
the process setpoint can be adjusted by using ▲ or ▼ to change the value while the
mode is running. Press Menu to display the High Limit Setpoint.
Pressing Run/Hold while in Timer Mode puts control in Hold status. The Timer LED will
flash to indicate Hold status. Press Run/Hold key again to continue timing. The Timer
LED will return to lit status.
- ULTRAFLEX DRYING AND FIRING 1
- FURNACE 1
- OWNER’S MANUAL 1
- Revision History 2
- 4 Version 2 4
- 1. About This Manual 6
- 1.5. Specifications 9
- Danger! 10
- 3. Theory of Operation 12
- Display Functions 13
- 14 Version 2 14
- 3.3. Modes and Menus 15
- 3.5. Key Functions 16
- 3.6. Outputs 16
- 3.4. Indicators 16
- HEORY OF OPERATION 17
- SSEMBLY & SETUP 19
- 20 Version 2 20
- 5.1. Start-up Basics 21
- 5.2. Manual Mode 22
- 5.3. Timer Mode 23
- 5.4. Profile Mode 24
- 5.5. Auto Start Mode 24
- 5.6. Setup Mode 25
- 5.6.3. Program Page 26
- PERATION 27
- 28 Version 2 28
- 5.6.4. Sample Profile 30
- 32 Version 2 32
- 5.6.6. Setting Up PID Page 33
- 34
- 36 Version 2 36
- 38 Version 2 38
- 40 Version 2 40
- 42 Version 2 42
- 44 Version 2 44
- 6. Maintenance 45
- 46 Version 2 46
- 8. Appendices 47
- 48 Version 2 48
- Profile Name: 49
- Profile Number: 49
- Control Page Default Values 50
- PPENDICES 51
- 52 Version 2 52
- Test Page Default Values 53
- 3rdDraft— 56
Relacionado con productos y manuales para Panel De Control Despatch Protocol Plus Controller (Heat Only)
(53 paginas)LG LHD627B manuály
Uživatelské manuály a uživatelské příručky pro DVD přehrávače LG LHD627B.
Poskytujeme 1 manuály pdf LG LHD627B ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales